HACKER SAFE certified sites prevent over 99% of hacker crime.

Enter Your Email Address to Receive Monthly Coupons and Special Discounts !

Credit Card Online Payments
XTREME K9 is UpFront

  Home > StayNCharge >

  All Charge 24/36V
Charge your trolling motor batteries while running on the water.


 
Our Price: $244.45



Availability:: Usually Ships in 24 Hours
Product Code: STAYNCHARGE-ALL-CHARGE-24-36
Qty:

Description
 

STAY'N CHARGE ALL CHARGE

The All Charge system is designed to enhance any charging system that you are already using.

By installing the All Charge system you will be able to top off your trolling batteries every time you crank the outboard motor and move to your next fishing location.

The unit can also be used to charge up to four batteries from a single Ac charger. By using the All Charge with a single bank AC charger you can charge the starting battery and up to three trolling batteries at the same time.

The new All Charge is designed to automatically know how many batteries it will be charging, if the batteries are wired correctly, and if the batteries are chargeable.

Very simply - use your trolling motor for an hour - spend 10 minutes running to your next fishing location and arrive with a full charge on the batteries. How awesome is that?

STAY'N CHARGE ALL CHARGE
The Best and Last Boat Battery Charger you will ever buy!
Price: $219.99

 
 
 

ALL CHARGE INSTALLATION INSTRUCTIONS

1. Locate the central point in the trolling battery compartment wall between the trolling battery,

2. Install the Smart box on the wall closest to the middle of the trolling batteries with the box facing out and the mounting brackets top to bottom.

3. Connect the battery wires from batt, 1 to the battery that the positive cable goes to the positive directly to the trolling motor making sure red goes to positive and black goes to negative.

4. Connect the battery wires from batt, 2 to the battery that the negative cable goes to the negative directly to the trolling motor making sure red goes to positive and black goes to negative.

5. Run the red and black wires with the plug end supplied from the trolling battery compartment to the boat’s starting battery compartment making sure that the circuit breaker goes to the boat’s starting battery. Make sure that the wires are not going to rub against anything that could rub or scrap the wires while the boat is bouncing around.

6. Connect the plug-in to the Smart Box first.

7. Hook the black wire to the negative side of the boat’s starting battery and tighten.

8. Install the circuit breaker close to the positive side of the boat’s starting battery. Hook the red wire to one side of the circuit breaker making sure the copper side of the circuit breaker is closest to the boat’s starting battery.

9. Hook one side of the short red jumper wire to the copper side of the circuit breaker and tighten down making sure the terminals on top of the circuit breaker have no chance of being touched (grounded out) by any metal objects. Take some electrical tape and cover the terminals.

10. Hook the other side of the red jumper to the positive terminal of the boat’s starting battery and tighten down.

11. Go back and make sure all of the connections are tight.
 
 
 
Jim Payne, the owner of Retrotect StayNCharge, installs the Original StayN'Charge and the AllCharge on B.A.S.S. Elite Pro Mark Menendez's Skeeter. (Part 1)
 
 
Jim Payne, the owner of Retrotect StayNCharge, installs the Original StayN'Charge and the AllCharge on B.A.S.S. Elite Pro Mark Menendez's Skeeter. (Part 2)
 

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

StayNCharge


All Charge 24/36V-TowNCharge Combo $329.99
All Charge 12/24V and TowNCharge Combo Pack $274.99
All Charge 12/24V $188.99
StaynCharge Tow N Charge
Peak Performance 2 Body Builder with Lutimax
MVP Formula M.A.S.S. K9 Muscle Builder
MVP Best In Show
MVP K9 Ingnite Electrolyte Formula
MVP K9 Optimal Health Program